騰達AC10V3路由器不斷重啟，求編程器固件

nmwinter

騰達AC10V3路由器不斷重啟，電源檢測沒問題，天線無短路，每次到網(wǎng)線口開始工作時就重啟，ping也只能ping通3行，懷疑固件問題，由于網(wǎng)口無法正常工作，無法通過網(wǎng)頁刷機，求編程器固件

邪惡海盜

啥配置的，果照呢？


二○二五年十一月二十九日

nmwinter

騰達AC10 v3配置
RTL8197FH  主控
RTL8812FR  5G芯片
RTL8367RB  千兆交換芯片

nmwinter

Booting...
init_ram

DDR init OK
init ddr ok

DRAM Type: DDR2
        DRAM frequency> 533MHz
        DRAM Size: 128MB
JEDEC id 684015, EXT id 0x6840
found BH25D16

>>>>>No Flash Vendor support (0x00684015)<<<<<

use MXIC as flash vendor instead
Flash is locked!
BH25D16, size=2MB, erasesize=4KB, max_speed_hz=55000000Hz
auto_mode=0 addr_width=3 erase_opcode=0x00000020
Write PLL1=80c00042
=>CPU Wake-up interrupt happen! GISR=89000080

RTL8197F-VG boot release version:599 (Feb 26 2020-11:10:32) (999MHz)
Mac addr:d8-32-14-ed-40-c0
LAN WAN isolate config...
Lan pbmp:0x000000ef
Wan pbmp:0x000000f0
use Switch new descriptor
wait for upgrage
port[0] link:down
port[1] link:down
port[2] link:down
port[3] link:down
port[4] link:down
irq:0x00008480
Jump to image start:0x80700000...
decompressing kernel:
Uncompressing... done, booting the kernel.
done decompressing kernel.
start address: 0xa0000600
[cyg_net_init] Init: mbinit(0x00000000)
[cyg_net_init] Init: cyg_net_init_devs(0x00000000)
Init device 'rltk819x_eth0'
Init device 'rltk819x_eth1'
Init device 'rltk819x_eth7'
Init device 'rltk819x_peth0'
[peth0] added, mapping to [eth1]...
Init device 'rltk819x_eth4'
Init device 'rltk819x_eth3'
Init device 'rltk819x_eth2'
Init device 'rltk819x_wlan1'
[MACFM_software_init 297]wifi hal support Mac function = 0x8008
RFE TYPE =0
[pwlan0] added...
Init device 'rltk819x_wlan1-vxd'
[MACFM_software_init 297]wifi hal support Mac function = 0x8008
RFE TYPE =0
Init device 'rltk819x_wlan1-va3'
[MACFM_software_init 297]wifi hal support Mac function = 0x8008
RFE TYPE =0
Init device 'rltk819x_wlan1-va2'
[MACFM_software_init 297]wifi hal support Mac function = 0x8008
RFE TYPE =0
Init device 'rltk819x_wlan1-va1'
[MACFM_software_init 297]wifi hal support Mac function = 0x8008
RFE TYPE =0
Init device 'rltk819x_wlan1-va0'
[MACFM_software_init 297]wifi hal support Mac function = 0x8008
RFE TYPE =0
Init device 'rltk819x_wlan0'
[MACFM_software_init 297]wifi hal support Mac function = 0x10ff
[pwlan0] added...
Init device 'rltk819x_wlan0-vxd'
[MACFM_software_init 297]wifi hal support Mac function = 0x10ff
Init device 'rltk819x_wlan0-va3'
[MACFM_software_init 297]wifi hal support Mac function = 0x10ff
Init device 'rltk819x_wlan0-va2'
[MACFM_software_init 297]wifi hal support Mac function = 0x10ff
Init device 'rltk819x_wlan0-va1'
[MACFM_software_init 297]wifi hal support Mac function = 0x10ff
Init device 'rltk819x_wlan0-va0'
[MACFM_software_init 297]wifi hal support Mac function = 0x10ff
Init device 'rltk819x_pwlan0'
[cyg_net_init] Init: loopattach(0x00000000)
[cyg_net_init] Init: ifinit(0x00000000)
[cyg_net_init] Init: domaininit(0x00000000)
[cyg_net_init] Init: cyg_net_add_domain(0x80471e00)
New domain internet6 at 0x00000000
[cyg_net_init] Init: cyg_net_add_domain(0x8047153c)
New domain internet at 0x00000000
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, logging disabled
Realtek FastPath:v1.03
[cyg_net_init] Init: cyg_net_add_domain(0x804713ec)
New domain route at 0x00000000
[cyg_net_init] Init: call_route_init(0x00000000)
[cyg_net_init] Init: ip6_init2(0x00000000)
[cyg_net_init] Init: sysctl_register_all(0x00000000)
[cyg_net_init] Done
Creating Init Thread...
cpuload_calibration_value=11103374
Envram is initing! base_addr=0x1c000 size=0x3000
md5:842cb400c67b09de org:00b42c84de097bc6
Nvram is initing! base_addr=0x1f8000 size=0x7fff
Snvram is initing! base_addr=0x1f0000 size=0x7fff
md5:45c7557a029d08e8 org:7a55c745e8089d02
md5:45c7557a029d08e8 org:7a55c745e8089d02
NVRAM start form MAIN block data
spi_lock.........
System start
Realtek GPIO init
Init GPIO in GPIO_APIV2
init gpio_id:33
init gpio_id:54
init gpio_id:35
init gpio_id:54
init gpio_id:40
init gpio_id:36
this thread can be checked ! if thread stack overflow or soiled
------------main
tenda_ifconfig error
: Invalid argument
CLI> [MAIN->tapf_vlan_config->262]:vlan config ok!
bridge0: ifid: 02:e0:4c:ff:fe:f0:00:01
in6_ifattach_linklocal: failed to configure a link-local address on bridge0 (errno=22)
kbMrAiIdNg-e>1b:r _iifniidt:- >0827:8e]0::b4rc(:bfrfi:dfgee:0f)0 :i0n0i:t0 1o
n!i
6_ifattach_linklocal: failed to configure a link-local address on bridge1 (errno=22)
tMeAtIhN:- >ibfri_di:n idta-:>3827:81]4::bfrf(:bfrei:degde:14)0 :icn0i
  ok!
[MAIN->init_before_module_init_services->76]:init_before_module_init_services ok!
[DEBUG] [MSG->msg_init->37]:rc_msg init ok!
[llm] br_interfaces(1065) eth0 up ...
eth0: promiscuous mode enabled
[MAIN->tapf_vlan_config->262]:vlan config ok!
[rc->rc_msg_2_tlv->108]:key = op,value = 3
[MSG->msg_send_msg_2_mbox->120]:center:00000106
[MSG->msg_send_msg_2_mbox->136]:send msg [op=3] success!
[TPI->tpi_lan_start->151]:start success!
re865x_ioctl:5069, set port 4 0M FULL
wlan: ifid: da:32:14:ff:fe:ed:40:c1
chip_version=0x100f,WlanSupportAbility = 0x0
test 0x81cd5c00,0x30,0x1cd5e80,0x0,
test 0x81cd5c80,0x30,0x1cd5ec0,0x0,
test 0x81cd5d00,0x30,0x1cd5f00,0x0,
test 0x81cd5d80,0x30,0x1cd5f40,0x0,
test 0x81cd5e00,0x30,0x1cd5f80,0x0,
[97G] RFE type 0 PHY paratemters: DEFAULT
clock 40MHz
InitMACTRX OK
InitMACProtocolHandler OK
InitMACSchedulerHandler OK
InitMACWMACHandler OK
InitMACSysyemCfgHandler OK
InitMACFunctionHandler OK
[Warning] is_fcs_mode_enable=NULL
--- STA STEERING INIT ---
LED2SV & LED1SV ctrl fem
steer_update_bss_info: isdown(0)
steer_update_bss_info: isdown(1)
chip_version=0x100f,WlanSupportAbility = 0x0
test 0x81cd5c00,0x30,0x1cd5e80,0x0,
test 0x81cd5c80,0x30,0x1cd5ec0,0x0,
test 0x81cd5d00,0x30,0x1cd5f00,0x0,
test 0x81cd5d80,0x30,0x1cd5f40,0x0,
test 0x81cd5e00,0x30,0x1cd5f80,0x0,
[97G] RFE type 0 PHY paratemters: DEFAULT
clock 40MHz
InitMACTRX OK
InitMACProtocolHandler OK
InitMACSchedulerHandler OK
InitMACWMACHandler OK
InitMACSysyemCfgHandler OK
InitMACFunctionHandler OK
LED2SV & LED1SV ctrl fem
steer_update_bss_info: isdown(0)
wlan1: promiscuous mode enabled
sTPI->twplia_nw:i fiif_iodp:e rdaat3r2-:>1145:4f8f]::fsetepd :s4u0c:cce5s
h!c
ip_version=0x2001,WlanSupportAbility = 0x3
clock 40MHz
InitPON OK!!!
>>SetBeaconDownload88XX
[GetHwReg88XX][PHY_REG_PG_8812Fmp_Type0]
[Warning] is_fcs_mode_enable=NULL
[set_8812F_trx_regs] +++
steer_update_bss_info: isdown(0)


sta steer cmd:count = 1, 0


sta steer cmd:count = 17, 2,rssi_lmt_2g,-55


sta steer cmd:count = 17, 2,rssi_lmt_5g,-76


sta steer cmd:count = 17, 2,pri_rssi_5g,-64


sta steer cmd:count = 17, 2,pri_rssi_2g,-74


sta steer cmd:count = 18, 2,sta_lmt_flow,100


sta steer cmd:count = 18, 2,sta_balance_en,1


sta steer cmd:count = 19, 2,sta_lmt_num_5g,16
wlan0: promiscuous mode enabled
pTPI-i>ntiptiW_ewbisf:i _loapneirpa=t[o1r9-2>.1156488.]0:.s1t]o
- s-u-c-c-e-s-s-!-
--w-lianni0t W e b s -c-l-e-a-r-_-a-c-l-_-t-a2b7l0e-:-0- - -
-w-l-a-n-1
     clear_acl_table:0  
wlan0     fflush_acl_list:0  
wlan1     fflush_acl_list:0  
func:ipnat_init i = 0
[TPI->tpi_firewall_start->239]:start success!
[TPI->tpi_http_start->145]:http start success!
[TPI->tpi_upnp_start->107]:start success!
osl_open_udp_socket: bind failed: Can't assign requested address
[TPI->tpi_dnsmasq_start->75]:start success!
[TPI->tpi_sntp_start->82]:start success!
[TPI->tpi_dhcp_server_start->330]:start success!
[TPI->tpi_wan_surf_check_start->588]:start success!
[TPI->tpi_wan_mode_check_update_info->75]:mode_need_switch is not yes!
[TPI->tpi_reboot_check_start->469]:start success!
[ERROR] [TPI->tpi_wifi_switch_sched_update_info->67]:schedule count[ 0 ] wrong
iw_init,1094,ifname2G:wlan1,ifname5G:wlan0
irute_force_attack_mitigation Th[rtepsiH_oilgdm[p1_0i]n
]t
0[W1i2F6i] [Sliummpilnea iCso]n fniogt hvi2n.g1 4t-ow pdso2..
  (2020.09.08-09:06+0000).

WIFI led mode end
[TPI->tpi_create_wps_thread->276]:start success!
wps_led_off,wps_led_blink_flag= 0


[TPI->tpi_wps_iw_start->320]:start success!
[ERROR] [TPI->tpi_ddns_start->105]:the mib is off, connot start!
.....ucloud.............do......option....
[TPI->tpi_ucloud_start->101]:start success!




[TPI->tpi_led_start->453]:start success!
[TPI->tpi_switch_led_start->118]:start success!
[MAIN->init_after_module_init_services->87]:init_after_module_init_services ok!
[rc->rc_module_msg_handle->157]:start handle module[6,rc_firewall]'s msg,op=3.debug_id=0.wlan_ifname=.string_info=
[TPI->tpi_firewall_action->137]p=3
ioctl(SIOCIPFFL): Invalid argument
[TPI->tpi_firewall_stop->263]:stop success!
wlan0     clear_acl_table:0  
wlan1     clear_acl_table:0  
wlan0     fflush_acl_list:0  
wlan1     fflush_acl_list:0  
func:ipnat_init i = 0
[TPI->tpi_firewall_start->239]:start success!

Booting...
init_ram

DDR init OK
init ddr ok

DRAM Type: DDR2
        DRAM frequency: 533MHz
        DRAM Size: 128MB
JEDEC id 684015, EXT id 0x6840
found BH25D16

>>>>>No Flash Vendor support (0x00684015)<<<<<

use MXIC as flash vendor instead
Flash is locked!
BH25D16, size=2MB, erasesize=4KB, max_speed_hz=55000000Hz
auto_mode=0 addr_width=3 erase_opcode=0x00000020
Write PLL1=80c00042
=>CPU Wake-up interrupt happen! GISR=89000080

RTL8197F-VG boot release version:599 (Feb 26 2020-11:10:32) (999MHz)
Mac addr:d8-32-14-ed-40-c0